No products in the cart.
How to Choose a CubePilot Autopilot: Cube Orange, Orange+, Blue H7, Purple, Black or Red
By the AT Group OÜ engineering team · Last updated: 26 October 2026
For most new UAV builds, choose the Cube Orange+. CubePilot names the Orange line its long-term stable option, and the Orange+ moves it to a dual-core STM32H757 processor. Choose the Cube Red when you need two flight management units, four IMUs and Ethernet. Avoid the Cube Black for new designs: its sensors are end-of-life.
Key facts at a glance
- Every Cube has three IMUs and two barometers: two IMUs on a vibration-damped board, one fixed on the flight management unit (FMU). [1]
- Cube Orange and Orange+ heat their IMUs with onboard resistors to keep them at a stable working temperature. [2]
- Cube Orange+ firmware is not interchangeable with Cube Orange firmware: each has its own build target in PX4 and ArduPilot. [3][4]
- Cube Red is a dual-FMU autopilot: 2 × STM32H7, 4 IMUs, 3 barometers and 3 CAN FD ports. [5]
- Ideal operating temperature for the Cube family is −10 °C to 55 °C. [6]
CubePilot autopilots compared
| Model | Processor | RAM | Sensors | ArduPilot target | Status |
|---|---|---|---|---|---|
| Cube Orange+ | STM32H757, dual-core | 1 MB | 3 IMUs, IMU board v3, heated and isolated | CubeOrangePlus |
Recommended for new designs |
| Cube Orange | STM32H753 | 1 MB | 3 IMUs, IMU board v2, heated and isolated | CubeOrange |
Original H7 Orange |
| Cube Blue H7 | STM32H753 | 1 MB | 3 IMUs, IMU board v2, CAN FD | n/a | Current H7 model |
| Cube Purple H7 | STM32H753 | 1 MB | 3 IMUs | CubePurple |
Replaced Purple F4 |
| Cube Black | STM32F427 | 256 KB | 3 IMUs, IMU board v1 (end-of-life sensors) | CubeBlack |
Legacy fleets only |
| Cube Red | 2 × STM32H7, Cortex-M7 + M4 | n/a | 4 IMUs, 3 barometers, 3 CAN FD, Ethernet | CubeRedPrimary / CubeRedSecondary |
Highest redundancy |
Sources: processors and RAM [7]; IMU boards [8]; Orange/Orange+ heating [2]; Cube Red [5]; ArduPilot targets [4]. “n/a” means the manufacturer documentation we cite does not state the value.
What is the difference between Cube Orange and Cube Orange+?

The Cube Orange+ uses a more powerful dual-core STM32H757 processor and newer IMUs; the Cube Orange uses an STM32H753. [3][7] Both have 2 MB flash and 1 MB RAM. [7]
The sensors differ too. ArduPilot lists an ICM20602 IMU for the Orange and an ICM42688 for the Orange+, each paired with an ICM20948 IMU/magnetometer and an MS5611 barometer. [2] CubePilot documents the Orange+ IMU board as version 3, with parts that vary by production batch. [8]
The practical consequence is firmware. PX4 states that “the firmware for Cube Orange+ and Cube Orange are not compatible”. The Orange+ needs its own board configuration, bootloader and build target, and is supported from PX4 v1.14. [3] ArduPilot also ships separate CubeOrange and CubeOrangePlus firmware. [4] When you replace an Orange with an Orange+, flash the Orange+ firmware.
Choose Orange+ for any new airframe. People still search for “Cube Orange” by name, but the Orange+ is the current version of the same family.
When do you need the Cube Red?
Choose the Cube Red when a single flight controller failure must not end the mission. It has two STM32H7 microcontrollers, a primary and a secondary, each a dual-core Cortex-M7 + Cortex-M4 with a double-precision floating point unit. [5]
Redundancy runs through the whole module: [5]
- 4 IMUs: 3 on the primary controller, 1 on the secondary.
- 3 barometers: 2 on the primary, 1 on the secondary.
- 3 CAN FD ports: one per controller plus one shared port that serves as a backup if a failure occurs.
- 10/100BaseT Ethernet, USB-C and an isolated static air port for stable barometer readings.
ArduPilot supports it with two firmware targets, CubeRedPrimary and CubeRedSecondary. [4] The Cube Red has its own standard carrier board pinout [15], so plan the carrier together with the module.
Is the Cube Black still a good choice?

Not for new designs. The Cube Black uses an STM32F427 with 256 KB RAM [7], and its MPU9250, LSM303D and L3GD20 sensors have reached end of life. [9] CubePilot’s service bulletin SB_0000006 asks users to plan the move to Orange, which it calls “the new Long Term Stable (LTS) option”. [10]
The Cube Black+ keeps the F4 processor with newer sensors, and CubePilot positions it only for users who cannot switch to Orange. [10] If you maintain a Cube Black fleet, the H7 Cubes (Blue H7, Orange and Purple H7) are plug-and-play with carrier boards that follow CubePilot’s reference design. [9]
Where do the Cube Blue H7 and Cube Purple fit?

The Cube Blue H7 shares the Cube Orange’s STM32H753 processor, 1 MB RAM and version 2 IMU board. [7][8] CubePilot lists the Blue H7 and the Orange as the Cubes with a CAN FD interface. [1]
The Cube Purple H7 replaced the Cube Purple F4. [9] It runs an STM32H753 with 1 MB RAM. [7]
On NDAA: CubePilot states that it is NDAA compliant and Executive Order 13981 compliant, and that the statement applies to all its products except Herelink. [11] NDAA compliance is therefore not a reason on its own to choose one Cube colour over another. Check the current statement for your procurement file.
Which carrier board should you use?
Use a full-size carrier board when you want a dedicated second power input; use the mini carrier when space matters more. On the “PRO” carrier board, the second power input is a dedicated plug. The mini carrier board still takes its backup power from the servo rail. [1]


All Cubes share the same core I/O: [1]
- 14 PWM servo outputs (8 from the I/O processor, 6 from the FMU).
- 5 general-purpose serial ports, 2 with flow control.
- 2 CAN bus interfaces, 2 I2C ports and 3 analog inputs.
- R/C inputs for CPPM, Spektrum/DSM and S.Bus.
Two external I2C ports let you connect two GPS/compass units without the compasses conflicting. [1] The ADS-B carrier board adds an integrated uAvionix ADS-B IN receiver on Serial 5, with the same overall footprint as the standard carrier. [2] It is included in our Cube Orange+ Standard Set. [12]
If no standard carrier fits your airframe, you can design your own around the Cube’s connector. The H7 Cubes are plug-and-play with carriers that follow CubePilot’s reference design. [9]
ArduPilot or PX4?
ArduPilot ships stable firmware for the Orange, Orange+, Purple, Black and Red; PX4 documents the Orange and Orange+. Firmware targets differ by model: [3][4][14]
| Model | ArduPilot (stable) | PX4 |
|---|---|---|
| Cube Orange+ | CubeOrangePlus |
cubepilot_cubeorangeplus (v1.14+) |
| Cube Orange | CubeOrange |
supported [14] |
| Cube Purple | CubePurple |
n/a |
| Cube Black | CubeBlack |
n/a |
| Cube Red | CubeRedPrimary, CubeRedSecondary |
n/a |
ArduPilot also offers -heli builds for helicopters and -bdshot builds for bidirectional DShot on the Orange and Orange+. [4] Check the current target list before flashing, because targets are added over time.
Typical configurations
The setups below are illustrative, built from the specifications above. They are not customer projects.
Survey or mapping VTOL. Cube Orange+ on the ADS-B carrier board (Standard Set) with a Here 4 RTK GNSS. The ADS-B IN receiver shows nearby manned traffic [2], and a second GNSS unit can be blended in ArduPilot (GPS_AUTO_SWITCH = 2). [13] For an RTK mapping build, see Cube Orange+ with RTK for mapping in Europe.

Compact multirotor. Cube Orange+ Mini Set or Cube Purple on the mini carrier board. Remember that the mini carrier takes backup power from the servo rail, not from a dedicated second input. [1]

High-redundancy platform. Cube Red with its dedicated carrier board. Two FMUs, four IMUs and a shared backup CAN FD port [5] suit operations where the autopilot must survive a single-point failure.
Frequently asked questions
Is Cube Orange+ firmware compatible with the Cube Orange?
No. PX4 states that the firmware for the two is not compatible, and ArduPilot provides separate CubeOrange and CubeOrangePlus targets. [3][4]
Does every Cube have three IMUs?
Yes. Every Cube has three IMUs, two on the vibration-damped IMU board and one fixed on the FMU, plus two barometers. The Cube Red has four IMUs and three barometers. [1][5]
What temperature range can a Cube operate in?
CubePilot gives −10 °C to 55 °C as the ideal operating range and 100 °C as the maximum during emergencies. Below freezing, CubePilot recommends preheating the module and watching for condensation. [6]
Which Cube is NDAA compliant?
CubePilot states that it is NDAA and Executive Order 13981 compliant, and that the statement covers all its products except Herelink. [11]
Can I connect two GPS units to a Cube?
Yes. The two external I2C ports allow two GPS/compass units without compass conflicts [1], and ArduPilot can blend two GPS units to reduce the chance of glitches. [13] For choosing the GNSS itself, see our guide to CubePilot’s Here series.
Is the Cube waterproof?
No. CubePilot states that the Cube needs external waterproof protection. [6]
Get a quote for CubePilot in Europe
AT Group OÜ is an official CubePilot distributor in Europe. The full range is available, including the Cube Orange+, Blue H7, Purple, Black and Red, carrier boards, Here 3+, Here 4, HerePro and Herelink. To connect Herelink to your Cube, follow our Herelink setup guide.
Request a quote → for configured kits, volume pricing or models not listed in the shop.
Sources
- CubePilot — The Cube specifications: https://docs.cubepilot.org/autopilot/the-cube/introduction/specifications
- ArduPilot — The Cube Orange/+ With ADSB-In Overview: https://ardupilot.org/copter/docs/common-thecubeorange-overview.html
- PX4 — CubePilot Cube Orange+ Flight Controller: https://docs.px4.io/main/en/flight_controller/cubepilot_cube_orangeplus
- ArduPilot — Copter stable firmware: https://firmware.ardupilot.org/Copter/stable/
- CubePilot — Cube Red specifications: https://docs.cubepilot.org/autopilot/cube-red/specifications
- CubePilot — The Cube operating conditions and performance: https://docs.cubepilot.org/autopilot/the-cube/introduction/the-cube-operating-conditions-and-performance
- CubePilot — Flight Management Unit (FMU): https://docs.cubepilot.org/autopilot/the-cube/introduction/flight-management-unit-fmu
- CubePilot — Vibration damped IMU board versions: https://docs.cubepilot.org/autopilot/the-cube/introduction/vibration-damped-imu-board-versions
- CubePilot — EOL and replacement: https://docs.cubepilot.org/autopilot/the-cube/introduction/eol-and-replacement
- CubePilot — SB_0000006 Time to Go Orange: https://docs.cubepilot.org/service-bulletins-and-critical-notices/safety-service-bulletins/sb_0000006-time-to-go-orange
- CubePilot — US Defence: https://docs.cubepilot.org/us-defence
- atgroup.store — Cube Orange+ Standard Set: https://atgroup.store/product/cube-orange-standard-set/
- ArduPilot — GPS Blending: https://ardupilot.org/copter/docs/common-gps-blending.html
- PX4 — CubePilot Cube Orange Flight Controller: https://docs.px4.io/main/en/flight_controller/cubepilot_cube_orange
- CubePilot — Cube Red standard carrier board pinout: https://docs.cubepilot.org/carrier-boards/cube-red-standard-carrier-board-pinout
